home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Programming Sound Cards
/
Programming Sound Cards.iso
/
sound_56
/
dmastp9a.asm
< prev
next >
Wrap
Assembly Source File
|
1995-01-01
|
17KB
|
444 lines
;══════════════════════════════════════════════════════════════════════════════
; Play with Cxh/Bxh commands on SoundBlaster 16/16ASP
; André Baresel (with some help from Craig Jackson)
;──────────────────────────────────────────────────────────────────────────────
; STATUS: DOES WORK ON SB16
;──────────────────────────────────────────────────────────────────────────────
; Requirements: 80286, SoundBlaster 16/16ASP (see BASEADDR,DMA channel,IRQ number)
; Resolutions : 8-bit / stereo / 4..44khz
; Parameters : none
; Note : Before compiling this call first "VOC2RAW TEST1.VOC /I /R"
; to creat "TEST1.INC" in this case a file with 8bit mono signed data
;
; ■ DSP command 41h ... set sample rate
; ■ DSP command D0h ... Halt Autoinit 8 bit DMA operation
; ■ DSP command D4h ... Continue Autoinit 8 bit DMA operation
; ■ DSP command C6h 020h ... autoinit 8 bit stereo data with no sign
;
.MODEL small
.286
; CONSTANTS ───────────────────────────────────────────────────────────────────
; SoundBlaster SETUP
BASEADDR EQU 0220h ;SoundBlaster base address
IRQ7 EQU 15 ;SoundBlaster IRQ
DMAchannel EQU 1 ;SoundBlaster DMA channel
; PIC MASKS FOR MASK/DEMASK IRQ
PICANDMASK EQU 01111111b ;'AND' PIC mask for clear IRQ7
PICORMASK EQU 10000000b ;'OR' PIC mask for set IRQ7
; DMA CONTROLLER REGISTERS :
WRITEMASK EQU 00ah ;WRITE MASK REGISTER
WRITEMODE EQU 00bh ;WRITE MODE REGISTER
CLEARFLIPFLOP EQU 00ch
PAGE_CHN EQU 083h ;PAGE REGISTER FOR DMAchannel 1
BASE_CHN EQU 002h ;BASEADDRESS REGISTER DMAchannel 1
COUNT_CHN EQU 003h ;COUNT REGISTER DMAchannel 1
; SAMPLERATE :
RATE EQU 02AEDh ; = 10989 Hz
; DMA WRITE MODE
WANTEDMODE EQU 01011000b ; singlemode, autoinit, readmode
;──────────────────────────────────────────────────────────────────────────────
; MACRO DEFINITIONs
;──────────────────────────────────────────────────────────────────────────────
STARTUP MACRO
; MASM 5.x COMPATIBILITY
__start: mov ax,DGROUP
mov ds,ax
mov bx,ss
sub bx,ax
shl bx,004h
mov ss,ax
add sp,bx
ENDM
WAITWRITE MACRO
LOCAL loopWait,endloop
; Arguments : DX = Status port (BASEADDR+0Ch)
; Returns : n/a
; Destroys : AL
push cx
xor cx,cx ; need that for slow SBs !
loopWait: dec cx
jz endloop
in al,dx ; AL = WRITE COMMAND STATUS
or al,al
js loopWait ; Jump if bit7=1 - writing not allowed
endloop: pop cx
ENDM
WAITREAD MACRO
LOCAL loopWait,endloop
; Arguments : DX = Status port (normaly BASEADDR+0Eh)
; Returns : n/a
; Destroys : AL
push cx
xor cx,cx ; need that for slow SBs !
loopWait: dec cx
jz endloop
in al,dx ; AL = DATA AVAILABLE STATUS
or al,al
jns loopWait ; Jump if bit7=0 - no data available
endloop: pop cx
ENDM
RESET_DSP MACRO
local SBthere
; Arguments : n/a
; Returns : n/a
; Destroys : DX,AL
mov dx,BASEADDR+06h
mov al,1
out dx,al ; start DSP reset
in al,dx
in al,dx
in al,dx
in al,dx ; wait 3 µsec
xor al,al
out dx,al ; end DSP Reset
add dx,08h ; dx = DSP DATA AVAILABLE
WAITREAD
sub dx,4 ; dx = DSP Read Data
in al,dx
cmp al,0aah ; if there is a SB then it returns 0AAh
je SBthere
jmp RESET_ERROR ; No SB - exit program
SBthere:
ENDM
;─── End of Macrodefinitions ──────────────────────────────────────────────────
.STACK 100h
.DATA
;──────────────────────────────────────────────────────────────────────────────
; Creat TEST1.INC with calling "VOC2RAW TEST1.VOC /I /R" or creat your own
; textfile with sampledata
SAMPLEBUFFER LABEL BYTE
INCLUDE TEST1.INC
SAMPLEBUFFEREND LABEL BYTE
PART db 1
information db 13,10,'DMASTP9A.EXE - play 8bit unsign stereo data (only SB16/SB16ASP)'
db 13,10,'Pause playing with key "p" and continue it then with any key.'
db 13,10,'Stop playing with <ESC>.','$'
memerror db 13,10,'Not enough memory to creat the DMA buffer','$'
txtpart0 db 13,10,'playing part 0','$'
txtpart1 db 13,10,'playing part 1','$'
sberror db 13,10,'No SoundBlaster at this BASEADDR ! PROGRAM HALTED.','$'
OLDInterruptSEG dw ?
OLDInterruptOFS dw ?
DMAbufferOFS dw ?
DMAbufferPage db ?
SAMPLEBUFFERLENGTH = offset SAMPLEBUFFEREND - offset SAMPLEBUFFER
;──────────────────────────────────────────────────────────────────────────────
.CODE
STARTUP
; FIRST FREE NOT USED MEMORY :
mov bx,ss
mov ax,es
sub bx,ax
mov ax,sp
add ax,15
shr ax,4
add bx,ax
mov ah,04ah
int 21h
; NOW ALLOCATE DMABUFFER
mov bx,SAMPLEBufferlength+15
shr bx,3 ; cx = samplebufferlength*2/16
; (count of 16byte blocks)
mov ah,48h
int 21h
jnc enoughmem ; ok got the memory
mov dx,offset memerror
mov ah,9
int 21h ; WRITE MSG 2 SCRN THAT THERE'S NOT ENOUGH MEM
jmp return2dos
enoughmem: ; AX = segment of DMA buffer / offset = 0
;──────────────────────────────────────────────────────────────────────────────
; calculate page and offset for DMAcontroller :
;
; segment*16+offset = 20bit memory location -> upper 4 bits = page
; lower 16 bits = offset
;──────────────────────────────────────────────────────────────────────────────
rol ax,4
mov bl,al
and bl,00fh
and al,0f0h
mov [DMABufferOFS],ax
mov [DMAbufferPage],bl
;──────────────────────────────────────────────────────────────────────────────
; check for DMApage override :
; ... problem: DMA controller separates memory into 64KB pages, you can only
; transfer data is placed in one page - no page overrides are allowed
;──────────────────────────────────────────────────────────────────────────────
; To solve that :
; creat a DMA buffer with double size you want - if the first part is placed
; on a page border the second part is for sure not
;──────────────────────────────────────────────────────────────────────────────
mov cx,SAMPLEBUFFERLENGTH
neg ax ; ax = 65536 - ax (bytes left to DMA page border)
cmp ax,cx
ja nooverride
; USE SECOND PART :
neg ax ; ax = offset first data
add ax,cx ; use second part
inc ax ; cx+1 bytes to next part ;)
mov [DMABufferOFS],ax
inc [DMABufferPage] ; 2nd part is on next page !
nooverride:
;──────────────────────────────────────────────────────────────────────────────
; Now move the sampledata into the DMAbuffer
; in a MODplayer you'll do that in the IRQ,
; but in our case we only repeat the same sound in the DMAbuffer
;──────────────────────────────────────────────────────────────────────────────
; FIRST CALCULATE THE DOS SEG/OFS FROM DMAPage/OFS
mov al,byte ptr [DMABufferOFS]
and al,0fh
xor ah,ah
mov di,ax ; di = offset of DMAbuffer
mov ax,[DMABufferOFS]
and al,0f0h
or al,[DMABufferPage]
ror ax,4
mov es,ax ; es = segment of DMABuffer
mov si,offset samplebuffer
; DS:SI - samples in dataseg
; ES:DI - DMABuffer
; CX - count of samples
;
rep movsb
RESET_DSP
; WRITE INFOMRATION TO SCREEN :
mov dx,offset information
mov ah,9
int 21h ; write program information to screen
; ENABLE SB SPEAKERS (for all SBs <SB16)
mov dx,BASEADDR+00Ch ;DX = DSP Write Data or Command
WAITWRITE
mov al,0D1h ; AL = Enable speaker
out dx,al ; Output: DSP Write Data or Command
; SETUP IRQ :
xor ax,ax
mov es,ax ; es to page 0 (Interrupt table)
mov si,IRQ7*4 ; si = position in interrupt table
; DISABLE IRQ (if it was enabled somehow)
in al,021h
and al,PICANDMASK ; SET MASK REGISTER BIT TO DISABLE INTERRUPT
out 021h,al
; CHANGE POINTER IN INTERRUPT TABLE
mov ax,es:[si]
mov [OLDInterruptOFS],ax ; save offset of old interupt vector for restoring
mov ax,OFFSET OWN_IRQ
mov es:[si],ax ; set offset of new interrupt routine
mov ax,es:[si+2]
mov [OLDInterruptSEG],ax ; save segment of old interupt vector for restoring
mov ax,cs
mov es:[si+2],ax ; set segment of new interrupt routine
; CHANGE PIC MASK :
in al,021h
and al,PICANDMASK ; CLEAR MASK REGISTER BIT TO ENABLE INTERRUPT
out 021h,al
mov cx,SAMPLEBUFFERLENGTH-1
;──────────────────────────────────────────────────────────────────────────────
; Setup DMA-controller :
;
; 1st MASK DMA CHANNEL
;
mov al,DMAchannel
add al,4
out WRITEMASK,al
;──────────────────────────────────────────────────────────────────────────────
; 2nd CLEAR FLIPFLOP
;
out CLEARFLIPFLOP,al
;──────────────────────────────────────────────────────────────────────────────
; 3rd WRITE TRANSFER MODE
;
mov al,WANTEDMODE
add al,DMAchannel
out WRITEMODE,al
;──────────────────────────────────────────────────────────────────────────────
; 4th WRITE PAGE NUMBER
;
mov al,[DMAbufferPage]
out PAGE_CHN,al
;──────────────────────────────────────────────────────────────────────────────
; 5th WRITE DMA BASEADDRESS
;
mov ax,[DMABufferOFS]
out BASE_CHN,al
mov al,ah
out BASE_CHN,al
;──────────────────────────────────────────────────────────────────────────────
; 6th WRITE BASECOUNTER = SAMPLELENGTH-1
;
mov al,cl
out COUNT_CHN,al
mov al,ch
out COUNT_CHN,al
;──────────────────────────────────────────────────────────────────────────────
; 7th DEMASK CHANNEL
;
mov al,DMAchannel
out WRITEMASK,al
;──────────────────────────────────────────────────────────────────────────────
; Setup SoundBlaster :
;
; 1st SET SAMPLERATE
;
mov dx,BASEADDR+00Ch ;DX = DSP Write Data or Command
WAITWRITE
mov al,041h ;AL = Set DAC Samplerate
out dx,al
WAITWRITE
mov cx,RATE
mov al,ch
out dx,al
WAITWRITE
mov al,cl
out dx,al
;──────────────────────────────────────────────────────────────────────────────
; 2nd play stereo unsigned data (DSPC C6h 20h XX XXh)
;
WAITWRITE
mov al,0C6h ;AL = DMA DAC 8bit autoinit
out dx,al
WAITWRITE
mov al,020h ;AL = stereo unsigned data
out dx,al
mov cx,SAMPLEBUFFERLENGTH
shr cx,1 ; after every half buffer report
dec cx
WAITWRITE
mov al,cl ;AL = LOWER PART SAMPLELENGTH
out dx,al
WAITWRITE
mov al,ch ;AL = HIGHER PART SAMPLELENGTH
out dx,al
; TRANSFER STARTs.....NOW.... :)
waitloop: mov ah,01 ;AH = Check for character function
int 016h ; Interrupt: Keyboard
jz waitloop ; wait for a key (sound in background)
xor ah,ah ;Read character, flush keypress
int 016h ; Interrupt: Keyboard
cmp al,'p' ; check for pause key
je pause ; ok
cmp al,27
jne waitloop
jmp exit ; other key so stop playing
pause: ; NOW HALT PLAYING :
mov dx,BASEADDR+00Ch ;DX = DSP Write Data or Command
WAITWRITE
mov al,0D0h
out dx,al
; WAIT FOR ANY KEY
xor ah,ah ;Read character, flush keypress
int 016h ; Interrupt: Keyboard
; NOW CONTINUE PLAYING
mov dx,BASEADDR+00Ch ;DX = DSP Write Data or Command
WAITWRITE
mov al,0d4h
out dx,al
jmp waitloop
exit: RESET_DSP
; RESTORE PIC MASK
in al,021h
or al,PICORMASK ;<-- SET REGISTER MASK BITS TO DISABLE
out 021h,al
; RESTORE IRQ :
xor ax,ax
mov es,ax ; es to page 0 (Interrupt table)
mov si,IRQ7*4
mov ax,[OLDInterruptOFS]
mov es:[si],ax ; set old interrupt routine
mov ax,[OLDInterruptSEG]
mov es:[si+2],ax
; CLEAR KEYBUFFER
mov ah,01
int 16h
jz return2dos
xor ah,ah ;Read character, flush keypress
int 016h ; Interrupt: Keyboard
; TERMINATE EXE:
return2dos:
mov ax,04c00h
int 21h
; display information if Soundblaster is not on this baseaddress
RESET_ERROR:
mov dx,offset sberror
mov ah,9
int 21h ; text output
jmp return2dos
;──────────────────────────────────────────────────────────────────────────────
; Our own IRQ for detecting buffer half SB currently plays
; It's generated by the SoundBlaster hardware
;──────────────────────────────────────────────────────────────────────────────
OWN_IRQ: pusha
mov dx,BASEADDR+00Eh ;DX = DSP DATA AVAILABLE (IRQ ACKNOWLEDGE)
in al,dx
mov ax,@data
mov ds,ax
mov dx,offset txtpart0
cmp [part],0
je notpart1
mov dx,offset txtpart1
notpart1: mov ah,9
int 21h ; text output
neg [part]
inc [part] ; part = 1-part result : 0,1,0,1,0,....
mov al,020h
out 020h,al ;ACKNOWLEDGE HARDWARE INTERRUPT
popa
IRET
END __start
